ADV-M™ Series

Advance ADV-M™ Series is ideal for reliable disinfection performance for a wide range of marine, salt water, highly chlorinated water and disinfection applications. ADV-M™ Series is designed and built for long term, trouble free performance in corrosive environments.

Advance ADV-M™ Series is popular because of its robust build quality and long term hassle free performance backed by knowledgeable application advice from an experienced team.

Advance ADV-M™ Series uses robust quality HDPE or PVC-U UV reactors, high performance quartz UV lamps matched with tuned electronic ballasts in a single lamp reactor configuration to deliver reliable disinfection performance.

Advance ADV-M™ Series UV systems are very easy to install, easy to use and easy to maintain.

Advance ADV-M™ Series is ideal for disinfection in corrosive environments like saltwater disinfection, marine disinfection, seawater disinfection, saltwater treatment plants, seawater RO plants, etc.

Features & Benefits

  • Reliable disinfection performance
  • UV dose modeling software based design
  • Robust, corrosion resistant construction in HDPE or UPVC
  • Non-chemical, no residues, no change to water chemistry
  • Very economical (typical disinfection cost is below fraction of a cent per litre of water)
  • Robust quality for long life, trouble free operation
  • Easy to install
  • Easy to use
  • Easy to maintain
  • Single lamp or multiple lamp UV reactors
  • Turbulent flow for uniform UV dose distribution
  • High performance monochromatic ultraviolet lamps with peak wavelength at 254nm
  • Tuned electronic ballasts
  • High %UVT quartz thimbles
  • Custom units available

Applications

UV System Selection

Sizing of correct UV unit depends on factors including

  • Desired UV Dose
  • Peak flow rate
  • %UVT10 of water

Advance ADV-M™ Series for water with 80-98%UVT

The table below shows Advance ADV-M™ Series UV units for EOL (end of lamp life) UV Dose of 25mJ/cm2 (250J/m2) @98%UVT10.
Contact us for UV system sizing based on other combinations of Peak Flow Rate, %UVT & UV Dose Requirement.

ADVANCE ADV-M™ SERIES UV SYSTEM PEAK FLOW @250 J/M2 [Ltr/Min] PEAK FLOW @250 J/M2 [M3/HR] ELECT. POWER [W] CONNECTIONS
ADV-M400 633 38 42 2” Union
ADV-M500 111 6.67 80 2” Union
ADV-M700 113 6.8 80 2” Union
ADV-M1100 222 13.34 140 2” Union
ADV-M1600 288 17.3 190 2” Union
ADV-M1800 345 20.7 200 2” Union
ADV-M2000 615 36.92 275 3” Flange
ADV-MF150 3,250 195 1,500 4” Flange

Wide Choice of Power Supply Boxes

Different versions available all with standard 10A GPO plug and 2m lamp lead.

Advance – BRK™ Power Supply

Suitable for all models from ADV-C50 to ADV-C400 Includes visible and audible lamp fail alarm, for indoor operation only. Dimensions: 105 x 60 x 30 mm, Weight: 0.4 kg

Advance – DDCV™ Power Supply

Suitable for all models from ADV-C50 to ADV-C1800 Includes visible and audible lamp fail alarm, volt free contacts (BMS), lamp operation count down timer 365- 0days, lamp change alert, for indoor operation only. Dimensions: 205 x 75 x 53 mm, Weight: 0.7 kg

Advance PRO™ Power Supply with UV Intensity Monitor

Available from all ADV-C series models includes power on indicator, visible and audible lamp fail alarm, UV Intensity Monitor, volt free contacts (BMS) optional, hours run meter, IP65(IP54 for fan cooled versions). Dimensions:300 x 300 x 150 mm, Weight:5.5 kg

ADV-M™ Series Power Supply Comparison

FEATURE BRK DDCV Series PRO
System Status Indicators
UV Lamp Fail Alarm
UV Lamp Hour Counter
UV Lamp Change Pre-Alert Optional
UV Lamp Change Reminder Optional
Volt Free Contacts (BMS)for fault indication Optional
UV Intensity Monitor 36.92 Optional
VFCs for Low UV Intensity Alarm 195 Optional
Fan Cooling with Air Filter Not Required IP21 (IP65 optional) (When Required)
Protection Class IP21 (IP65 optional) IP23 (IP65 optional) Optional IP65 for some models (IP54 for fan cooled versions)

Options: (additional cost)

  • UV intensity monitor & sensor
  • Stainless steel enclosure or glass reinforced polyester enclosure
  • Spare set of volt free contacts (BMS)
  • Longer lamp lead
  • Different mains supply
  • Chamber thermostat with solenoid valve for over-temperature protection
  • Sampling ports
  • Quartz sleeve wiper (manual)
  • Thermal Relief Value
  • 12/24V DC input (for ADV-C50 to ADV-C400)
  • Twin chamber Configuration
  • Z configuration (Water fitting on opposite sides of chamber)

Advance ADV-M™ Series Spare Parts

To get the desired disinfection performance from your Advance M™ Series UV unit, we recommend regularly servicing the UV unit, replacing the UV lamp, O ring and cleaning the quartz thimble.

Advance C™ Series UV lamp numbers are etched on the lamp body near the pins and include UV Lamp LL020-S4™, UV Lamp LL020-S4-O™, UV Lamp LL030-S4™, UV Lamp LL030-S4-O™, UV Lamp LL040-S4™, UV Lamp LL040-S4-O™, UV Lamp LL046A-S4™, UV Lamp LL079-S4™, UV Lamp LL080-S4™, UV Lamp LL120-S4™, UV Lamp LL127-S4™, UV Lamp LL172-S4™, UV Lamp LL180-S4™, UV Lamp LL180-S4-O™, UV Lamp LL235-S4™, UV Lamp LL235-S4-O™, UV Lamp LL320-S4™, UV Lamp LL450-ST4™ and UV Lamp LL450-ST4-O™.

To check the Advance UV Lamp number hold the lamp against light and clear background. You can also write down the reactor number with RE prefix from the stainless steel UV chamber before contacting us or your nearest Advance UV sales & service partner.

Contact us for with any UV related questions or your Advance UV Lamp number and Advance UV reactor number for advise or any Advance UV lamps, Advance UV quartz sleeves, Advance UV ballasts, Advance UV O rings, Advance UV sensors and Advance UV spare parts. We would be delighted to put you in contact with the right Advance UV sales and service partner for Advance UV spares & service.

Advance ADV-M Series: Technical Summary

OPERATING PARAMETER GENERALLY RECOMMENDED RANGE
Peak Flow Rate (m3/hr) [Note1] 0.5m3/hr to 195m3/hr
Peak Flow Rate (lpm) [Note1] 10lpm to 833lpm
%UVT10 40% to 98%+
Operating Water Pressure (kg/cm2) 1kg/cm2 to 10kg/cm2
Operating Water Temperature 4oC to 60oC
Input Power Required 230V AC, 50-60Hz OR 12V DC

* Contact us for model selection to suit your application
Note1: Recommended peak flow rate depends on factors like desired EOL UV Dose, %UVT of water, etc.